數控五金加工的順序是什么？?對于加工行業中，順序是很重要，它關系到產品的質量保證，有一道順序弄錯了，就容易造成很大的損失，嚴重的話的要重頭來過，有點嚴重，就是這些產品就報廢了，數控五金加工就是其中的一個，那么它的順序有哪些？

一、數控五金加工順序的安排應根據零件的結構和毛坯狀況，以及定位夾緊的需要來考慮，重點是工件的剛性不被破壞。?（1）上道工序的加工不能影響下道工序的定位與夾緊，中間穿插有通用數控五金加工工序的也要綜合考慮。?（2）先進行內形內腔加工序，后進行外形加工工序。?（3）以相同定位、夾緊方式或同一把刀加工的工序最好連接進行，以減少重復定位次數，換刀次數與挪動壓板次數。?（4）在同一次安裝中進行的多道工序，應先安排對工件剛性破壞小的工序。?

二、刀具集中分序法?就是按所用刀具劃分工序，用同一把刀具加工完零件上所有可以完成的部位。在用第二把刀、第三把完成它們可以完成的其它部位。?這樣可減少換刀次數,壓縮空程時間，減少不必要的定位誤差。??

三、以加工部位分序法?對于加工內容很多的零件，可按其結構特點將加工部分分成幾個部分，如內形、外形、曲面或平面等。?一般先加工平面、定位面，后加工孔；?先加工簡單的幾何形狀，再加工復雜的幾何形狀；?先加工精度較低的部位，再加工精度要求較高的部位。?以上就是數控五金加工的順序，按照這幾條來進行操作，這才會讓您的數控五金加工風險大大的減少。